Something goes wrong with the power and the first question is usually the same: is this a quick fix or something bigger. A breaker that keeps tripping, an outlet that stopped working, lights that flicker when the furnace kicks on, or a panel that buzzes when nothing obvious is wrong. Those symptoms point in different directions, and knowing which one you are dealing with before anyone shows up saves time and keeps the scope honest. We handle that conversation on the call, and we handle the work across Westminster and the surrounding area.
Homeowners dealing with a specific fault, property managers keeping a multi-unit building up to code, and commercial tenants fitting out a space all come to us with different needs. The process is the same for all of them. You call, describe what you are seeing, and we scope the job on the phone before anything is booked. We cover Westminster every day from 8:30 AM to 10:30 PM, including weekends, so a problem that surfaces on a Saturday morning does not have to wait.
Electrical systems get outpaced. A home wired for the loads of a few decades ago was not designed for an EV charger, a high-draw range, electric heating, and the rest of what a modern household runs at the same time. The panel that handled it fine before starts tripping breakers under normal use. Circuits that were shared get overloaded. The wiring itself may not be rated for the current being asked of it.
The first step is a load calculation. That tells us what the existing service can actually carry and where the gaps are. Sometimes the answer is a dedicated circuit for the appliance that is causing the problem. Sometimes the panel itself needs to be replaced or upsized. In some cases the service entrance, the point where the utility supply meets the home's wiring, also needs to be upgraded before a larger panel makes sense.
We go through that on the call and confirm the scope before scheduling anything. You get straight answers about your panel and wiring, including what the panel can carry and what it cannot, before any work begins.
Some electrical problems will not keep. A dead circuit in a rental unit, a panel fault in a building that cannot go dark, or a wiring issue that came up during a pre-closing inspection all have timelines attached to them. Short-notice calls are welcome, and the schedule is checked on the spot to find the earliest opening. We are available every day from 8:30 AM to 10:30 PM, which means the window for reaching us is wide.
When you call, the person who answers knows the trade and can scope the job on the phone. That matters for short-notice work because it means the visit is scoped before arrival, not figured out on site. Prompt response, even for last-minute electrical calls, is part of how we operate.
A tenant who cannot vacate, a retail space that needs to stay open, or a landlord who is not on site when the work happens all require a bit of coordination. We work through access and timing on the call so the visit does not create a disruption that was not planned for. For landlords, we confirm what documentation is needed after the work is done, including what was found, what was replaced, and what the circuit or panel looks like now.
The rate is confirmed before anything is scheduled. What moves a quote is what the job actually involves: the fault that turns up once the circuit is traced, what has to be opened up to reach it, and whether the existing wiring or panel can carry the change being asked of it. A single outlet replacement is a short conversation. A panel upgrade with a service entrance change is a longer one.
We do not quote a flat rate for every job because the jobs are not all the same. What stays consistent is the process: scope confirmed on the call, price given before booking, and no revision to that number without a conversation before the additional work starts. You get a straight answer about the work before it is scheduled.
If you have questions about what a specific job covers, ask on the call. That is what the call is for.
Property managers and landlords in Westminster run into a recurring coordination problem. The person who books the work is not the person who lets us in, and the person who pays the invoice is not the person who describes the fault. We handle that arrangement regularly.
On the call, we confirm who is the point of contact for access, what the tenant has been told, and whether there are any constraints on the visit window. After the work is done, we go over what was found and what was done with whoever needs that record, whether that is the landlord, the property manager, or both. Code corrections that come up during the visit are discussed before they are carried out, not added to the invoice after the fact.
Older homes in Westminster can carry wiring that was installed to the standards of its time and has since been superseded. Knob-and-tube wiring, which routes conductors through open air and ceramic knobs rather than through a grounded sheath, is not compatible with modern circuit protection and cannot be extended or modified safely. Aluminum branch circuit wiring, which was used in residential construction during a period when copper prices ran high, requires specific devices and connection methods that many original installations did not include.
Neither of these is automatically a reason to rewire the whole house. What matters is the condition of the existing wiring, what loads it is being asked to carry, and whether any modifications or additions are planned. We assess that on the visit and explain what needs to be addressed and what can be left alone.
Some older panels were not undersized when they were installed. They became undersized as the household load grew around them. A 100-amp service that handled a home with gas heat and no EV charger is a different proposition once electric heating, a Level 2 charger, and modern appliances are added. Arc-fault and ground-fault breaker requirements have also expanded under successive code cycles, and older panels often cannot accommodate the updated protection without a replacement.
We handle subpanel installations where the main panel is at capacity but the service entrance can support the additional load. Where the whole panel needs to come out, we scope the replacement, the service entrance, and the circuit layout as a single job. Before booking anything, our services page is worth a read.
Rewiring comes up when the existing wire is the wrong type for the application, when knob-and-tube or aluminum wiring needs remediation, or when a home addition or renovation opens up the walls enough to make it practical. We handle both full rewires and targeted partial rewires, scoped to what the property actually needs rather than a fixed scope that may do more or less than the situation calls for.
A dryer, an electric range, a wall oven, or a refrigerator running on a shared circuit creates a load the breaker was not sized for. The fix is a dedicated circuit sized to the appliance. We run new wire from the panel, install the correct breaker, and confirm the panel has capacity before the circuit is added. EV charger circuits follow the same process: load calculation first, then the circuit and outlet or hardwired connection.
Outdoor outlets need covers and enclosures rated for exposure to weather. In this region, that means covers that hold up through freeze-thaw cycles and hardware that does not corrode after a single winter. We install weatherproof GFCI outlets for exterior locations, including garages, decks, and utility areas, and confirm the circuit feeding them is properly protected.
These are among the most common dedicated circuit requests we handle. Each appliance draws a specific load at a specific voltage, and the circuit has to match. We pull the panel cover, confirm what capacity is available, run the wire, and install the correct outlet and breaker. If the panel is already at capacity, we scope the options before the visit is booked.
A stairwell, a hallway, or a room with two entry points often needs a switch at each end that controls the same fixture. Three-way switching is the standard solution. Where the existing wiring does not support it, we run the additional wire needed. Smart switches that handle multi-location control without a traditional traveler wire are also an option where the wiring configuration makes them simpler to install.
Security lighting, motion-activated fixtures, and landscape lighting all require circuits rated for outdoor use and connections that hold up in wet conditions. We run dedicated circuits for exterior lighting where the existing outdoor circuit is already loaded, install weatherproof junction boxes and fixtures, and confirm the wiring is rated for the exposure. For landscape lighting that involves multiple low-voltage fixtures, we handle the line-voltage side of the installation.
Flickering lights fixed. Dead outlets revived. Power back on.
Westminster is our primary focus on this page, and we cover the broader Adams County area as well. Nearby communities we serve regularly include Shaw Heights, Federal Heights, Sherrelwood, Northglenn, and Twin Lakes. If you are just outside Westminster and unsure whether your address falls within our service area, call and we will confirm it on the call.
Safe wiring. Solid workmanship. Straight answers.
Crawl space work involves accessing the area, confirming conditions are safe to work in, and running or repairing wiring within the space. We confirm what the access looks like on the call. If the space has standing water or structural issues that affect safe access, that affects how the job is scoped.
Usually yes. Power tools, compressors, welders, and car lifts draw more than a standard 15- or 20-amp circuit can supply, and running them on shared circuits leads to tripped breakers and undersized wiring. We size dedicated circuits for the equipment that will actually be used in the space.
We confirm access arrangements and the tenant's availability on the call before the visit is booked. The landlord or property manager stays in the loop on what was found and what was done, and any code corrections that come up during the visit are discussed before they are carried out. The invoice goes to whoever is responsible for it, and the access is arranged separately with the tenant.
In many cases, yes. If the work is on a circuit that does not feed the payment system, those outlets can stay live. We identify which circuits are affected before we start and confirm what will and will not be interrupted. That conversation happens when the job is scoped.
We start with a load calculation to confirm the existing panel can carry the additional circuit. If it can, we run a dedicated 240-volt circuit from the panel to the garage or parking area and install the outlet or hardwired connection the charger requires. If the panel is already at capacity, we scope a panel upgrade as part of the same job before anything is scheduled.
It does, because older homes can carry wiring types or panel configurations that change the scope of the job. Knob-and-tube wiring, aluminum branch circuits, and older panels that cannot accept arc-fault or ground-fault breakers all affect what is involved in a repair or upgrade. We ask about the age of the home and any known wiring history on the call so the scope reflects what is actually there.
Driveway and landscape lighting runs on low-voltage wiring fed from a transformer, or on line-voltage circuits where brighter fixtures are needed. We handle the circuit that feeds the transformer or the fixtures, confirm the wiring is rated for direct burial or conduit as the installation requires, and make sure the circuit is properly protected.
The electrical work itself is similar, but an apartment involves shared building infrastructure. The panel may serve multiple units, and work that affects common wiring or the building supply requires coordination with the building owner or manager. We go over the setup on the call to confirm what is accessible and what requires building-level coordination.
Shaw Heights, Federal Heights, Northglenn, and the rest of the area around Westminster are all covered.
When you call (720) 536-2956, you reach someone who knows the trade and can scope the job on the phone.
The rate is confirmed before anything is scheduled. We are available every day from 8:30 AM to 10:30 PM. Call Littleton Electrical Company for a quote and we will take it from there.
Electrical work also reaches these towns: Northglenn, Broomfield, Arvada, Thornton, Wheat Ridge.
For every town we reach, see our coverage area.
Below is a plain-language look at the electrical work we handle in Westminster and the surrounding area. Each service is described by what it covers, who it fits, and one practical thing worth knowing before you call. If a job you need is not on the list, call us and we will talk through it.
| Type of Work | What It Covers | Best For | Good to Know |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular |
| Homes adding EV chargers, electric ranges, or other high-draw appliances that push an older panel past its limit | A load calculation is part of every panel job. It confirms what the existing service can carry and what the new configuration needs to handle before anything is scheduled. |
| Whole-Home Surge Protection |
| Homeowners with sensitive electronics or anyone who wants every circuit in the building protected from a single installation | A panel-level surge protector covers every circuit in the home. Point-of-use strips at individual outlets do not provide that same whole-system coverage. |
| Heat Tape Installation |
| Homes in Westminster with pipes or roof edges at risk of freezing during extended cold snaps | Heat tape wiring must be rated for exterior and wet-location use. The circuit also needs proper protection, which is part of every heat tape installation we do. |
Call (720) 536-2956 to talk through the job and get a price before anything is scheduled. We are available every day from 8:30 AM to 10:30 PM.
(720) 536-2956